topblog Ivoire blogs

19/03/2018

Lonsdor K518ISE programdelete G chip to Toyota Corolla 2010-

How to: use Lonsdor K518ISE key programmer to add/program new keys or delete remotes to Toyota Corolla G chip.

Toyota Corolla

12-1

Toyota Corolla key

12-2

Toyota Corolla OBD location

12-3

How to:

Add new key (2010 Corolla with G chip)
Require: a master key
Insert the master key into the ignition, if the immo light does not turn on. And if the immo light turns on for about 1s, then off, the key is spare key.

Insert master key into the ignition, and turn it to “ON”, then waiting system communicating…
Insert the key to be added (don’t need to turn the key)
Wait for system programming, it will complete after a few seconds

Delete Keys (2010 chip)
Require: a master key.
Insert master key into the ignition,and turn it to “ON”,then waiting system communicating…
Insert the key you want to add(don’t need to turn the key)
Waiting for system programming,then deleting complete

Reset IMMO (when all keys are lost)
Note:After performing this operation, no need to reprogram immo controller (2010 chip)

After reset the immo, it will restore to default status.
Ignition off, then ignition on System programming, pls follow guide to turn on or turn off the ignition…pull out key.

Please complete the following steps within 120s:
Require: 2 master keys and 1 spare key
Insert first master key, ignition on and wait for 5 seconds.
Insert second master key, ignition on and wait for 4 seconds.
Insert the spare key, ignition on and wait for 5 seconds, then the immo light off, the programming complete.

Reset immo (2010 chip)

(no need reset immo if you’ve changed immo)

1 take out the key within 120s, insert the first key to be programmed

2 system communication, key programming completed

Remote programming

1 ignition on

2 press both Lock and Unlock buttons when programming all remotes within 30s. first press both buttons for 4s, then press Unlock button for 1s

3 remote programming completes.

12-4
12-5
12-6
12-7
12-8

Done with key programmer Lonsdor K518ISE here: http://www.cnautotool.com/goods-6636-Lonsdor+K518ISE+Key+Programmer+Plus+SKE-LT+Smart+Key+Emulator+.html

Delete remotes (Corolla 2010-)

1 ignition on

2 delete all remotes within 30s (press both Lock and Unlock buttons on remotes left for 4s, then press Unlock button for 1s)

Delete remotes successfully

12-9 12-10 12-11 12-12 12-13

Note:

2010 Corolla chip:

A master key is required to delete keys

How to know it’s a master key: insert the key into the ignition switch; if the immo light remains off, it’s the master key; if the light turns on then off, it’s not the master key.

Remote 2010-

When programming remote, the system pops up: please press OK and finish remote matching within 30s.

How-to: press both Lock and Unlock buttons on remotes for 4s, then press Unlock button for 1s. To match more remotes, same way

Remote 2010-

When deleting remotes: press both Lock and Unlock buttons on remotes left for 4s, then press Unlock button for 1s

 

This articlle is published by CnAutotool.com

10/03/2018

CAR FANS C800 diesel vehicles coverage

CAR FANS C800 almost supports all brand heavy duty vehicles in market:35 Heavy duty brand, 21 BUS Brand, 16 Passenger car Brand, 32 Machinery vehicle brand and 46 ECU System.

Commercial Vehicle: FAW,DONGFENG, Mercedes-Benz, CNHTC, FOTON, SANY, JAC, SFH, CAMC, UD, VOLVO, Mitsubishi, IVECO, MAN, SCANIA, JMC, HINO, ISUZU, SHACMAN, C&C, Hyundai, XCMG, BEIBEN, KIA, KING LONG, YUTONG, HIGER, GOLDEN DRAGON, YOUNGMAN, BYD, ANKAI, DAEWOO, SUNWIN, ZHONGTONG, HUANGHAI, WZL, SUNLONG, TOYOTA, ASIASTAR

3-1

Passenger Vehicle: Mercedes-Benz, Hyundai, VW, Zhonghua, JMC, GreatWall, ZZNISSAN, JAC, ZXAUTO, DONGFENG, LIEBAO, CHERY, FUDI, GONOW, HUATAI, SSANGY, MAXUS, JX-ISUZU

3-2

Machinery: CAT, KOMATSU, VOLVO, SANY, LOVOL, JOHN DEERE, HITACHI, KOBELCO, HYUNDAI, ZOOMLION, CASE, LISHIDE, DOOSAN, SUMITOMO, YUTONG, Bobcat, SHANTUI, LiuGong, IHISCE, XCMG, KUBOTA, Takeuchi, XGMA, Atlas, TEREX, YUCHAI, LONKING, SUNWARD, SEM, Jonyang, PENGPU, YTO, JAC, XINYUAN, DXZG, HENGTE, SANYUAN, HUANGHE, SHUNTONG, STRONG

3-3

Engine&ECU: Bosch, Denso, Delphi, Perkins, Deutz, Weichai, Yuchai, Fawde, Cummins, Yunnei, Changchai, SDEC, DCD, Yangchai, Quanchai, EUP, JX-Isuzu, XCE, Kernel, SIDA

3-4

(1)Menu display area, including: truck system, bus system, passenger vehicles, engineering machinery, expert and
system settings.
(2)Model brand selection area: each model can be detected for all models brand.

CAR FANS C800 software upgrade

1.Log in the official website (www.carfans.net.cn )
2.Download and install the Diagnostic Tools for Truck C800 intelligent diagnostic device upgrade client software.
3.Plug in the device SD card through the card reader into the computer USB interface to finish the device software upgrade.

CAR FANS C800 language available

English & Chinese

CAR FANS C800 user manual

http://forobd2tool.com/wp-content/download/CAR%20FANS%20C800/cf-c800-user-manual-v1.2.pdf

C800 Package list:  

3-5

1pc * Power extension cord
1pc *Battery clip supply line
1pc *Cigarette lighter supply line
1pc *SD card
1pc *SD card reader
1pc *Test extension cord (with OBD connector)
1pc *Power adapter kit
1pc *C800 device
1pc *C800 carry case
1pc *OBD16PIN Circular adaptor
1pc *CUMMINS-9
1pc *IVECO-38
1pc *BENZ-14
1pc *KOMATSU-12
1pc *VOLVO-14
1pc *VOLVO-8
CAT-9
Multi-function jumper adaptor

C800 user manual

Accessories
CUMMINS-6
MITSUBSHI-12+16
DENSO-12
WIT-3
ISUZU-20
HITACHI-6
HITACHI-4
MAN-37
MAN-12
RENAULT-12

 

http://blogs.siliconindia.com/obdauto

04/03/2018

How to use BDM adapters with Ktag Kess KTM100 Dimsport

Here is a BDM adapter user manual for Denso, Marelli, Bosch, Siemens.

BDM probe adapters full set for sale:
http://www.cnautotool.com/
contact via Email: Sale@cnautotool.com

What is BDM?
BDM is an acronym for Background Debug Mode, an interface designed by the Motorola company, widely
used in automotive industry, present on modern ECUs. Not all ECUs are capable of interfacing
through the BDM – see Appendix for the list of ECUs that support the BDM interface.

What is Adapter?
ADAPTER is an electronic circuit board designed for a certain ECU (manufacturer), with pogo pins and a 10-pin IDC connector for interfacing the multiplexer board.

What is a BDM Adapter?
BDM adapter is an electronic circuit intended for BDM operation on supported ECU. The adapter provides pogo pin based connectors for interfacing the ECU BDM connector. Interfacing the supported tool is made by the use of intermediate circuit board (multiplexer) that connects to the adapter over the MUX connector and to the tool over the desired tool connector (FGTECH, XPROG, BDM100,Dimsport, KTM100, KESS V2 & K TAG, etc.)

26-1

26-2

What is a BDM Adapter Full Set?
Here is a list of BDM adapter full set: (support Denso, Marelli, Bosch, Siemens)
A full set includes 22pcs.

26-3

1 14AM00T01M Bosch
2 14AM00T02M Delphi DCM
3 14AM00T03M Bootloader ST10xx
4 14P600KT04 Infineon Tricore EDC/MED17
5 14AM00T05M Marelli MPC55xx JTAG
6 14AM00T06M Delphi MPC55xx JTAG
7 14AM00T07M Denso CN1 Boot
8 14AM00T08M Denso CN2 Boot
9 14AM00T09M Denso CN3 Boot
10 14AM00T10M Denso CN1 AUD
11 14AM00T11M Denso CN2 AUD
12 14AM00T00M Delphi DCI
13 14AM00TBAS Base Adapter 1.27
14 14AM00T14M NexusEFI T6 Lotus
15 14AM00TB02 Magneti Marelli BDM insert
16 14AM00TB01 Siemens BDM insert
17 14AM00TB03 EDC7 BDM insert
18 14AM00T18M Magneti Marelli MPC/SPC56xx
19 14AM00T13M Nexus MPC5xx TRW ECU
20 VAG 1.6tdi – Siemens-Continental PCR2.1
21 14AM00T15M Toyota NEC76F-20
22 14AM00T16M Toyota NEC76F-26

How to use a BDM probe adapter with KTAG/KESS/KTM100/Dimsport?

1.Open the ECU
○ at least one part of the casing (top or bottom) needs to be removed
○ refer to other sources (Internet) to get information on which part needs removing on your ECU

2.Locate the ECU BDM connector

○ usually a set of 10 – 12 pads in two rows (depending on the ECU)
○ pads may be 2.54 mm or 1.27 mm apart (depending on the ECU)
○ rows may be 2.54 mm or 5.08 mm apart (depending on the ECU)
○ if the ECU BDM connector can not be located, chances are that the BDM pads are scattered all over the ECU PCB in which case you can not use the adapter directly – nevertheless it is possible to manually route the adapter BDM signals to the ECU BDM pads (only for advanced users)

3.Locate the ECU BDM pin 1 position

○ pin 1 is usually not clearly marked on the ECU BDM pin out
○ on an ECU with the standard Motorola BDM pin out pins 3 and 5 are connected to ground – this can be checked either visually or using a multimeter tool
○ refer to other sources (Internet) to get more information on the pin 1 position for your ECU from CnAutotool.com

4.Place the desired adapter in the frame saddle

○ make sure the pogo pins are facing out
○ lift the saddle so that the ECU can be slided under the frame adapter saddle

5.Place the ECU on the frame

○ inspect the adapter for pogo pin 1 location which is clearly marked ○ rotate the ECU on the frame so that the adapter pogo pin 1 and ECU BDM pin 1 match
○ make sure ECU is firmly sitting on the frame
○ double check the ECU position

6.Connect the multiplexer board and adapter

○ at this point multiplexer board should be connected to the adapter via MUX connector
○ this will allow LEDs on the adapter to illuminate the area of interest (where the pogo pins need to touch the ECU BDM pads)
○ do not connect the tool yet

7.Connect the external power (+12 V) to the multiplexer

○ multiplexer external power is used to power the LEDs on the adapter allowing easier positioning of the adapter pogo pins on the ECU BDM pads
○ red LED on multiplexer board will light up when external power (+12 V) is present
○ at this point the white LEDs on the adapter should also light up
○ do not connect the tool yet

8.Fine tune the ECU position

○ lower the frame adapter saddle to almost touch the ECU BDM pads
○ each adapter pogo pin needs to sit on a separate ECU BDM pad
○ if pogo pins do not sit on the pads you may be using the wrong adapter – do not use the adapter in this case!

9.Lower the frame adapter saddle

○ each adapter pogo pin should sit on one ECU BDM pad
○ minimum down force should be applied when making the interconnection between the adapter and ECU

10.Double check the adapter pogo pin and ECU BDM pad interconnection

○ in order not to damage the ECU and/or tool make sure that the steps above have been performed correctly

11.Connect the tool to the multiplexer board

○ only connect one tool at any given moment to the multiplexer
○ make sure to use the correct 10-pin IDC connector (FGTECH, XPROG, BDM100&KTAG)for interfacing the tool used:
1 use provided 10-pin to 10-pin cable with FGTECH or BDM100 tools
2 use provided 10-pin to 16-pin cable with XPROG tool
3 use manufacturer 10-pin to 25-pin cable with KTAG tool

○ do not connect the tool to the 10-pin IDC connector labeled MUX
○ do not power up the tool yet

12.For Bosch adapter only

○ Bosch ECUs need to have ECU power supplied on the pogo pins (2 and 9)
○ some tools provide dedicated ECU power (BDM100, KTAG) while others do not (XPROG, FGTECH)
○ Bosch adapter can be used in both cases, providing that the jumper is properly placed on the 3-pin header (found on the adapter)
○ place the jumper on the adapter on the 3-pin header to the correct position:
○ place jumper over left and central pins when using XPROG and FGTECH tools – this will use +12 V power delivered from the multiplexer board (external power) for powering the ECU
○ place jumper over right and central pins when using BDM100 or KTAG tools – this will use +12 V power delivered by the tool for powering the ECU

13.For Siemens, Delphi and Marelli adapters only

○ Siemens, Delphi and Marelli do not provide ECU power on the pogo pins
○ in order to power the ECU +12 V and ground signals needs to be connected to the ECU separately(usually over the ECU interfacing connector)
○ in this case ECU power can be taken from multiplexer board connectors J2 (+12 V) and J3 (ground), otherwise provide the +12 V ECU power from additional source
○ refer to other sources (Internet) to get more information on the location of the +12 V and ground pin location for your ECU

14.Connect the tool to the PC (or power up the tool)

○ perform software installation as described by the tool manufacturer if not done already
○ at this point the multiplexer, adapter and the ECU should be properly interconnected with BDM signals and power lines
1 multiplexer red LED should be lit up
2 adapter white LEDs should be lit up
3 ECU power (+12 V) should be present

○ connect the tool to the PC (usually done over USB or serial connection)

15.Perform BDM operation(s)

○ start up the software package to operate the ECU Programmer
○ perform desired BDM operation(s)Note: The user manual is used for reference; in fact, it depends. Try on your own risk.

 

http://autotool.biz/2018/02/25/how-to-use-bdm-adapters-with-ktag-kess-ktm100-dimsport/